An unnoticeable recessed LED profile fixture
LED-INSER is a versatile light to be used both as a working light and a mood light, e.g. in a kitchen workspace or on shelves and other surfaces where light is needed! It is an aluminum profile fixture designed to be recessed in furniture. The profile is submerged to furniture level and only a sleek thin edge of the profile is visible. LED-INSER IP44 B is only 8.5 mm deep allowing installation on a sheeted wall without a need to change the wall support structures. The fixture can be shortened to a desired length.
LIMENTE LED-INSER IP44 B is available in standard lengths of 2 and 4 meters. The fixture can be shortened to a desired length at 3,3 cm intervals. LIMENTE LED-INSER IP44 B comes with quality LEDs with a color rendering index of Ra> 85, an efficiency of 80 lm/W, a luminosity of 1080lm/m and a color temperature of about 4000K (small color temperature differences may vary by production batches). The fixture includes a matte protective glass diffuser, which makes the light even and continuous and makes the light a bit warmer in light color. All technical values are given to the led strip without a diffuser.
In addition to LIMENTE LED-INSER IP44 B, LIMENTE LED-INSER is available in two different versions: the LUX collection version LIMENTE LED-INSER IP44 LUX (IP44, Ra>90, 3000K and 4000K) and the color temperature adjustable CCT version LIMENTE LED-INSER IP44 CCT (IP44, Ra>80, 2700K-6000K).
To use LIMENTE LED-INSER, you’ll need a suitable 24V power supply. Compatible products are mentioned alongside the product. The profile, the led strip and the power supply are also sold separately. N.B.! The power supply must be ordered separately.
Dimming and lighting control
Appropriate lighting for any occasion is made easy with our dimming and lighting control system. You can easily change the lighting and ambience in your home from efficient and bright to dim and cozy by dimming your LIMENTE LED-INSER IP44 B with our wireless system. You can use the same switch to adjust all the LIMENTE lights in the room, including various ceiling, panel and profile lights. The light adjusts smoothly at the same time while creating ambience for working, entertaining or any mood in between.
LIMENTE LED-INSER IP44 B is dimmable either with LIMENTE SMART 350 dimmer (no. 640351) and a wireless wall switch (no. 640352) or with LIMENTE SMART 400 24V dimmer (no. 640420) and wireless wall switches (no. 640411, 640421 and 640422, 640424, 640425). LIMENTE SMART 425 is a remote control, which you can use to adjust lighting in your home but also to save two different preset lighting settings to change the mood with just a click of a button!
The dimmer is installed between the power supply and the fixture. The dimmer includes a similar manifold to the one included in the power supply. You can connect up to 6 LIMENTE lights to one dimmer, as long as the maximum load (W) of the power supply is not exceeded.
LIMENTE LED-INSER IP44 B is fast and easy to install with the installation tools included.
The power supply cable is put in place (e.g. hidden behind a cabinet) so that the male connector comes close to the power supply and the female connector comes near the LED-INSER profile. A power supply cable at both ends of the fixture enables LED-INSER IP44 B to be used as two separate lights. The fixture can be shortened to a desired length at 3,3 cm intervals. There is a 5cm + 300cm long power cord at each end of the fixture. An extension cord (3m, no. 681588) can be ordered, in case a longer power cord is needed. Extension cords can be fitted with a maximum on 1 pcs of fixtures, with a maximum cord length of up to 6m. Please note the adequate length of the cord and the maximum load (W) of the power supply.
LED-INSER IP44 B can also be used in its full length (2 or 4 m). When wanting to use the whole length, simply cut off the power supply cable at the other end.
When installing, cut the profile into the desired length and attach in place with the installation tools and clips included. Remove the double-sided tape from the light strip and press onto the profile. Finally, connect the power supply cable to the light strip and to the power supply. All electrical connections are done with quick connectors.